Sale!
3D Printed Flush Cover for Panasonic FZ-M1 Barcode Reader Module Replacement
Original price was: $35.00.$25.00Current price is: $25.00.
Description
A brand-new, 3D-printed flush mount cover for removal of the Panasonic FZ-M1 Barcode Reader Module. This unit is custom-designed and built specifically to allow users to remove the factory-installed barcode reader from the FZ-M1 tablet and replace it with a weather-sealed cover–reducing weight and bulk.
APPLICATION
This custom-designed and 3D-printed cover is designed and built specifically for the Panasonic FZ-M1 tablet. The buyer will need to remove the factory barcode reader module (instructions are available online) and then install the new cover using the original hardware, including screws and weather seal. Panasonic FZ-M1 tablet, barcode reader, hardware, module seal, etc. are not included. You will receive only the cover itself.
This custom-designed and 3D-printed cover is designed and built specifically for the Panasonic FZ-M1 tablet. The buyer will need to remove the factory barcode reader module (instructions are available online) and then install the new cover using the original hardware, including screws and weather seal. Panasonic FZ-M1 tablet, barcode reader, hardware, module seal, etc. are not included. You will receive only the cover itself.
WARRANTY
Each unit is thoroughly inspected before shipping and should arrive ready to install with no issues. But just in case, this item is warrantied against manufacturer defects/damage during shipment and will be replaced, no questions asked, within 30 days of the date it arrives. After that date, simply reach out to us with any issues/concerns and we will work to find a solution.
WATER INGRESS PROTECTION
Please note that this replacement cover makes use of the original seal provided on the Panasonic FZ-M1, and as such cannot be guaranteed to prevent all water ingress. However, these have been tested on units with good seals and have been shown to have no water ingress with moderate application of water to the replacement cover. We highly suggest inspecting your unit’s seal during the install process, and to take precautions to avoid direct water impact on the unit. This unit has NOT been tested to be compliant with the factory IP65 rating, although again, there should be no issues at all if you have a good seal.You may optionally choose to use a silicone waterproof sealant with the hardware (such as Loctite), although this is not necessary for water ingress prevention if you have a good factory seal.
Please note that this replacement cover makes use of the original seal provided on the Panasonic FZ-M1, and as such cannot be guaranteed to prevent all water ingress. However, these have been tested on units with good seals and have been shown to have no water ingress with moderate application of water to the replacement cover. We highly suggest inspecting your unit’s seal during the install process, and to take precautions to avoid direct water impact on the unit. This unit has NOT been tested to be compliant with the factory IP65 rating, although again, there should be no issues at all if you have a good seal.You may optionally choose to use a silicone waterproof sealant with the hardware (such as Loctite), although this is not necessary for water ingress prevention if you have a good factory seal.
SHIPPING
These units are 3D printed on-demand. We try to keep a few units ready to ship, but depending on demand, we may need to print additional units in order to ship yours out. We will contact you directly after the sale to inform you of the time to print your unit, if required, and an estimated ship date.If we have stock on-hand at the time of sale, your unit will ship within 3 business days (although we try hard to get it out no later than the next day). This unit is shipped using USPS Ground Advantage in order to reduce costs for you. You will be provided a tracking number and your item is fully insured against damage during shipment.
These units are 3D printed on-demand. We try to keep a few units ready to ship, but depending on demand, we may need to print additional units in order to ship yours out. We will contact you directly after the sale to inform you of the time to print your unit, if required, and an estimated ship date.If we have stock on-hand at the time of sale, your unit will ship within 3 business days (although we try hard to get it out no later than the next day). This unit is shipped using USPS Ground Advantage in order to reduce costs for you. You will be provided a tracking number and your item is fully insured against damage during shipment.
MADE IN THE USA
The Panasonic FZ-M1 Barcode Reader Module Replacement Flush Cover was designed and 3D printed in the U.S.
The Panasonic FZ-M1 Barcode Reader Module Replacement Flush Cover was designed and 3D printed in the U.S.
Vendor Information
- Store Name: K8DDV's Backyard Hamshack
- Vendor: K8DDV's Backyard Hamshack
- 5.00 rating from 6 reviews
-
BDC-12AH Battery Distribution and Charging System
Price range: $450.00 through $550.00 K8DDV's Backyard Hamshack Select options This product has multiple variants. The options may be chosen on the product page -
Sale!
Digirig Replacement Cover
Original price was: $12.00.$10.00Current price is: $10.00. K8DDV's Backyard Hamshack Read more -
20W Dummy Load
$33.00 K8DDV's Backyard Hamshack Read more
Related products
-
Icom Stacking Brackets -7300 & 9700
$20.00 The 3D Printing Ham Add to cart -
Universal Handheld Ham Radio Wall Mount – 4 Pack
$9.95 CQSwag Add to cart -
Dual Band 2m / 70cm Vertical Dipole Antenna (Mast Mount)
$23.70 BarberTechnologies Add to cart -
Dual Band 2m / 70cm Vertical Dipole Antenna (Mark IV) (Vertical Flat Mount Only)
$77.00 BarberTechnologies Add to cart
5 reviews for 3D Printed Flush Cover for Panasonic FZ-M1 Barcode Reader Module Replacement
There are no reviews yet.